TUREF, UTM, ITRF: Türkiye'de doğru koordinat sistemini seçmek
Aynı noktanın farklı sistemlerde farklı sayıları vardır. Yanlış sistem seçilirse, sahada cm düzeyinde ölçtüğünüz nokta paftada metrelerce yana kayar. Bu yazıda ITRF, TUREF ve UTM'nin ne olduğunu, datum ile projeksiyon farkını ve Türkiye'de hangi sistemi ne zaman seçeceğinizi netleştiriyoruz.
Özet
- ITRF = küresel referans çerçevesi (datumun temeli). TUREF = Türkiye'nin ITRF tabanlı ulusal datumu.
- UTM ve TM birer projeksiyondur — datumu düzleme açma yöntemi.
- Kadastro genelde TUREF + 3° TM (TM27/TM30/TM33/TM36/TM39/TM42/TM45…), metre cinsindendir.
- Doğru dilimi, çalışma alanının boylamı belirler.
- En tehlikeli hata: eski ED50'yi TUREF/WGS84 ile karıştırmak → metrelerce kayma.
Önce kavram: datum mı, projeksiyon mu?
Bir koordinat sistemi iki ayrı karardan oluşur:
- Datum: Dünya'nın şeklini ve yere oturuşunu tarif eden model (ITRF, TUREF, WGS84, ED50). “Hangi Dünya?” sorusunu yanıtlar.
- Projeksiyon: Bu eğri yüzeyi düzleme nasıl açtığın (UTM, TM…). “Nasıl düzleştirildi?” sorusunu yanıtlar.
İkisi bağımsızdır. “TUREF / TM33” demek, TUREF datumu + 33° orta meridyenli TM projeksiyonu demektir. Bu ikisini ayırmadan koordinat konuşmak, en sık karışıklık kaynağıdır.
ITRF, TUREF ve WGS84
ITRF (International Terrestrial Reference Frame), küresel ve çok hassas bir referans çerçevesidir; dünya çapındaki istasyonlarla sürekli güncellenir. TUREF (Türkiye Ulusal Referans Çerçevesi), bu çerçeveye dayanan ulusal datumdur ve modern kadastronun temelidir. WGS84 ise GNSS/GPS ekosisteminde yaygın kullanılan küresel datumdur; TUREF'e pratikte çok yakındır. Üçü de moderndir ve birbirine yakındır — sorun bunlarda değil, eski sistemlerle karışmalarındadır.
Asıl tuzak: ED50
ED50 (European Datum 1950), Türkiye'de uzun yıllar kullanılmış eski bir datumdur. ED50 ile TUREF/WGS84 arasındaki fark birkaç yüz metreye varabilir. Eski bir paftadaki koordinatı modern bir GPS verisiyle düzeltme yapmadan birleştirirseniz, parselin yeri kayar. Bu yüzden her zaman verinin hangi datumda olduğunu netleştirmek gerekir.
Doğru TM dilimini seçmek
Türkiye'de büyük ölçekli işlerde 3 derecelik dilimli TM projeksiyonu kullanılır. Her dilim, orta meridyeniyle anılır ve çalışma alanınız bu meridyene ne kadar yakınsa çarpıtma o kadar azdır. Aşağıdaki tablo örnektir; Türkiye genelinde TM27'den TM45'e kadar farklı orta meridyenler kullanılabilir:
| EPSG | Sistem | Yaklaşık bölge |
|---|---|---|
| 5254 | TUREF / TM30 | Orta meridyen 30° (batı–orta) |
| 5255 | TUREF / TM33 | Orta meridyen 33° (İç Anadolu) |
| 5256 | TUREF / TM36 | Orta meridyen 36° (doğu–orta) |
| 4326 | WGS84 (derece) | GPS varsayılanı |
| 32635 / 32636 | WGS84 / UTM 35N–36N | 6° UTM dilimleri |
Pratik kural: çalışma alanının boylamına en yakın orta meridyenli dilimi seçin. UTM (6° dilim) küçük ölçekli ve GIS işlerinde, TM (3° dilim) kadastro ve büyük ölçekli işlerde tercih edilir.
GNSS, WGS84/TUREF ve proje teslimi
Alıcının ürettiği koordinat referansı, kullanılan düzeltme servisine ve ayarlara bağlıdır; proje teslimi ise genelde TUREF / TM metre bekler. Aradaki dönüşüm doğru datum, epok ve dilimle yapılmazsa, sahadaki cm düzeyi ölçüm paftada metreye dönüşür. Bu yüzden ölçüm öncesi proje koordinat sistemini netleştirmek, ölçümün kendisi kadar önemlidir.
Doğru dilimi seç, dönüşümü cebinde yap.
MapLab Survey, ölçüm verisini seçilen TUREF/UTM sistemine sahada çevirir; uygun EPSG/TM dilimini seçmenize yardım eder ve ölçümünüzü DXF, KML, GeoJSON, CSV olarak dışa aktarır. Kayıt, dönüşüm ve dışa aktarım çevrimdışı çalışır; datum/dilim seçimi proje şartnamesi ve kontrol noktalarıyla doğrulanmalıdır.
MapLab Survey'i indirSık sorulan sorular
TUREF, UTM, ITRF farkı nedir?
ITRF küresel çerçeve, TUREF onun Türkiye datumu, UTM ise bir projeksiyon. ITRF/TUREF "hangi Dünya", UTM "nasıl düzleştirildiği" sorusudur.
Kadastro hangi sistemi kullanır?
Genelde TUREF datumu + 3° TM projeksiyonu, metre cinsinden; bölgeye göre TM27/TM30/TM33/TM36/TM39/TM42/TM45 dilimi.
TM30/33/36 nedir?
3° TM dilimleri; orta meridyenleri 30°, 33°, 36°. Alanın boylamına en yakın olan seçilir.
WGS84 ile TUREF aynı mı?
Çok yakın ama aynı değil; ikisi de modern. Asıl tehlike eski ED50 ile karıştırmaktır.
İlgili: RTK GNSS ile cm düzeyinde doğruluk · Koordinat sistemleri dersi · MapLab Survey
TUREF, UTM, ITRF: choosing the right coordinate system in Türkiye
The same point has different numbers in different systems. Pick the wrong one and a cm-level field measurement shifts metres on the sheet. This article clarifies what ITRF, TUREF and UTM are, the difference between datum and projection, and which system to choose when in Türkiye.
Key takeaways
- ITRF = a global reference frame (the basis of a datum). TUREF = Türkiye’s ITRF-based national datum.
- UTM and TM are projections — how a datum is flattened onto a plane.
- Cadastre generally uses TUREF + 3° TM (TM27/TM30/TM33/TM36/TM39/TM42/TM45…), in metres.
- The right zone is set by the longitude of your work area.
- The most dangerous mistake: mixing the old ED50 with TUREF/WGS84 → metres of shift.
First the concept: datum or projection?
A coordinate system is two separate decisions:
- Datum: The model of the Earth’s shape and fit (ITRF, TUREF, WGS84, ED50). It answers “which Earth?”.
- Projection: How that curved surface is flattened (UTM, TM…). It answers “how was it flattened?”.
The two are independent. “TUREF / TM33” means the TUREF datum + a TM projection with a 33° central meridian. Talking coordinates without separating these two is the most common source of confusion.
ITRF, TUREF and WGS84
ITRF (International Terrestrial Reference Frame) is a global, highly precise reference frame, continuously updated from worldwide stations. TUREF (the Turkish National Reference Frame) is the national datum based on it, and the foundation of modern cadastre. WGS84 is the global datum widely used in the GNSS/GPS ecosystem, very close to TUREF in practice. All three are modern and close to one another — the problem isn’t them, it’s mixing them with older systems.
The real trap: ED50
ED50 (European Datum 1950) is an older datum used in Türkiye for many years. The difference between ED50 and TUREF/WGS84 can reach a few hundred metres. Combine a coordinate from an old sheet with modern GPS data without a transformation and the parcel moves. Always clarify which datum the data is in.
Choosing the right TM zone
Turkish cadastre uses a 3-degree TM projection. Each zone is named by its central meridian, and the closer your work area is to that meridian, the smaller the distortion:
| EPSG | System | Approx. region |
|---|---|---|
| 5254 | TUREF / TM30 | Central meridian 30° (west–central) |
| 5255 | TUREF / TM33 | Central meridian 33° (Central Anatolia) |
| 5256 | TUREF / TM36 | Central meridian 36° (east–central) |
| 4326 | WGS84 (degrees) | GPS default |
| 32635 / 32636 | WGS84 / UTM 35N–36N | 6° UTM zones |
Rule of thumb: pick the zone whose central meridian is closest to your area’s longitude. UTM (6° zones) suits small-scale and GIS work; TM (3° zones) suits cadastre and large-scale work.
GPS gives WGS84; what about cadastre?
The coordinate reference produced by the receiver depends on correction service and settings; project deliverables usually expect TUREF / TM in metres. If transformation is not done with the right datum, epoch and zone, a cm-level field point becomes metres off on paper. Clarifying the project coordinate system before surveying is as important as the survey itself.
Pick the right zone, do the conversion in your pocket.
MapLab Survey converts survey data to the selected TUREF/UTM system in the field, helps you choose the suitable EPSG/TM zone, and exports your survey as DXF, KML, GeoJSON, CSV. Recording, conversion and export work offline; datum/zone selection should still be checked against project specifications and control points.
Get MapLab SurveyFrequently asked questions
TUREF vs UTM vs ITRF?
ITRF is a global frame, TUREF is its Türkiye datum, UTM is a projection. ITRF/TUREF answer “which Earth”, UTM answers “how it’s flattened”.
Which system does cadastre use?
Generally TUREF datum + a 3° TM projection, in metres; the TM27/TM30/TM33/TM36/TM39/TM42/TM45 zone by region.
What are TM30/33/36?
3° TM zones with central meridians 30°, 33°, 36°. Pick the one closest to your area’s longitude.
Are WGS84 and TUREF the same?
Very close but not identical; both are modern. The real danger is mixing them with the old ED50.
Related: Centimetre accuracy with RTK GNSS · Coordinate systems tutorial · MapLab Survey