Land surveying in the USA: NAD83(2011), State Plane and NAVD88
In the United States a coordinate is complete only with four facts: datum, State Plane zone, which foot, and height datum.
Field takeaways
- The horizontal reference is NAD83(2011) (geographic EPSG 6318), maintained by NGS.
- State Plane (SPCS 83) has more than a hundred zones, mostly following state and county lines.
- SPCS 83 is defined in metres; conversion to feet uses the US survey foot or the international foot, as state law specifies.
- NAD83 and WGS84 differ by one to two metres across the conterminous states.
- Heights are NAVD88 (EPSG 5703); GNSS ellipsoid heights convert with GEOID18.
The horizontal frame: NAD83(2011)
NOAA's National Geodetic Survey (NGS) maintains the national reference. For the conterminous states, Alaska and Puerto Rico the current horizontal realization is NAD83(2011), epoch 2010.00 (geographic EPSG 6318). Archives also hold older realizations such as NAD83(HARN); the differences are usually centimetres, which still matters on control work.
State Plane: the zone is part of the coordinate
SPCS 83 divides the country into more than a hundred zones. Some states are a single zone; Texas has five, California six. Zones elongated east-west use Lambert Conformal Conic, those elongated north-south Transverse Mercator. A coordinate without its zone lands somewhere else entirely in the next zone.
Which foot?
SPCS 83 is defined in metres; conversion to feet follows the definition in each state's law: the US survey foot (1200/3937 m) or the international foot (exactly 0.3048 m). They differ by two parts per million, which on values in the millions of feet becomes a shift measured in feet. NIST and NGS deprecated the US survey foot for new work after 31 December 2022, but legacy files are still written in it.
WGS84, UTM and NAVD88
NAD83 is tied to the North American plate, while WGS84 practically coincides with ITRF; across the conterminous states they differ by one to two metres. Check which frame your RTK corrections use. UTM is common in regional mapping, zones 10 to 19 across the lower 48. Heights are NAVD88 (EPSG 5703); a NAD83(2011) ellipsoid height converts with GEOID18. NGS is preparing replacements (NATRF2022, NAPGD2022); until they take effect, label deliveries NAD83(2011) and NAVD88.
The app in the USA
MapLab Survey opens with the official coordinate system of the user's location in 148 countries and offers 564 coordinate systems, searchable by EPSG code. Search your State Plane zone by its EPSG code in the coordinate system list and check that it is the one your project uses — datum and foot definition included. RTK GNSS, offline work and DXF, KML or Shapefile export run in the same workflow.
Try these steps on your own phone.
MapLab Survey handles RTK/GNSS point capture, drawing, area and volume calculations and coordinate conversion, then exports to DXF, KML/KMZ, GeoJSON, Shapefile, GeoPackage, NCZ or CSV. Capture, calculation and export work offline. Live NTRIP corrections and online basemaps need a connection.
Frequently asked questions
Which coordinate system is official in the USA?
The horizontal reference is NAD83(2011); large-scale work mostly runs in State Plane (SPCS 83) zones, regional work in UTM. Heights are NAVD88.
Does the US survey foot versus international foot difference matter?
Yes. It is two parts per million, but on State Plane values in the millions of feet it becomes a shift measured in feet. The file should say which foot it uses.
Is my phone's GPS coordinate the same as NAD83?
No. WGS84 and NAD83(2011) differ by one to two metres across the conterminous states; check which frame your RTK corrections use.
How do I find my State Plane zone in the app?
Search the zone by its EPSG code in the coordinate system list and check that its datum and foot definition match your project.
Technical references
The field guidance in this article is aligned with the technical and official references below.
Related: Coordinate conversion app · GNSS Z and elevation · Bluetooth RTK GNSS · MapLab Survey